Slide Hammer Dent
Searching for affordable prices on a Slide Hammer Dent ? You came to the right place!
 |
 Performance Tool W89725 Slide Hammer Puller Set  US $89.99
|
 Performance Tool Slide Hammer Puller Set W89725 US $117.90
|
 REAR AXLE BEARING REMOVER PULLER SET PULLING TOOLS US $44.19
|
 Performance Tool W2029DB 9 Pc Dent Seal Puller Set US $35.80
|
 Starter Kit Plus Dent Repair Stud Welder Kit HSA4550 US $269.99
|
 Dent Fix Equip DF DM550DX Ding Massager Glue Puller Kit US $342.95
|
 Performance Tool Large Dent Puller W2016C US $30.00
|
 Performance Tool Compact Dent Puller W2015P US $20.00
|
 Dent Fix Equip DF 505 THE MAXI DENT REMOVAL STATION US $1,196.95
|
 Ding Massager Glue Puller Kit DENDF DM550DX BRAND NEW US $329.00
|
 Steck 20014 Stud Lever Stud Nail Puller US $38.99
|
 Snap On CJ 109 Slide Hammer Puller US $34.99
|
Some interesting information about Slide Hammer Dent
Dent Repair Methods
Minor dents are perfectly suited for non-intrusive dent repair. Working from the backside of the dent, a trained technician can gently work the metal outward using plastic-tipped punches. When the process is completed the dent completely disappears without the need for body fillers or paint. Such dent repairs are less expensive than traditional bodywork methods. The technicians often perform these repairs in the car owner's driveway or garage, eliminating the inconvenience of dropping off the vehicle and arranging alternative transportation.
If the dent is deeper or has caused permanent distortion of the surrounding metal, the repair will become much more intrusive, time-consuming and expensive. Such dents and damaged areas must be forced back outward by using a hammer and dolly to slowly move the metal back into shape and nearly flush with the surrounding surface. When it is difficult to gain access to the backside of a dent, or when the backside of the dent may be difficult to reach using a dolly, a small hole in the center of a dent is drilled for a bolt to be attached or to a pin welder is used to tack a pin or series of pins to the damaged surface. Using a slide-hammer attached to the bolt or pins, the dent is pulled outward until it is nearly flush with the surrounding surface.
After the dent has been pulled outward, the remainder of the dent repair is performed using plastic or resin body fillers applied in thin layers over the remaining dent until the surface is built up to the level of the surrounding surface. The body filler is sanded down using very coarse and fine sandpapers until the profile is correct and the body filler flows perfectly with the surrounding surface. Finally, the area must be primed and painted to match the rest of the vehicle.
About the Author
Mark Carpenter is co-owner of Dings Plus Paintless Dent Removal in San Jose, CA. For more information or to learn more about the benefits of paintless dent removal for your automobile or truck, please visit: http://www.dingsplus.com.
Questions on Slide Hammer Dent
Tuning slide stuck on my trumpet?
i am renting a cornet, and the biggest tuning slide is stuck. i have tuning slide grease, that worked for the others, but not the biggest one, i can't get it to move!! how can i get it unstuck myself without anything dangerous for me or my instrument.
i tried putting valve oil and tuning slide grease, didn't work. i also tried pouring hot water, didn't work either. i even tried hammering it, didn't work, just made a few dents in my cornet! what should i do? thanks!!
i don't know any shops that repair so if any do it yourself tips or how to do it, would help...
try butter
Thank you for browsing our resource. Hopefully you have found the Slide Hammer Dent you were wanting to buy.